![]() Connect the wires to the terminal block being certain to connect the positive wire to the terminal marked + and the negative wire to the terminal marked –. Using a flat-head screwdriver set the transformer tap to the correct tap setting for your installation.When using conduit attach the conduit connector to the terminal cover plate then connect the wires to the terminal block being certain to connect the positive wire to the terminal marked + and the negative wire to the terminal marked –. We strongly recommend testing the system with music to determine the correct output level. WARNING: Do not mount and finish over the speaker until you have selected the necessary tap setting to achieve the desired volume level. If necessary, re-select a lower or higher tap setting.Īfter selecting a given tap, play the speaker with an actual audio signal to verify the speaker provides adequate volume. Sonance DSP Amplifiers are recommended for use with the IS6T speaker. When using the IS6T in 70V/100V, we recommend the Sonance DSP-2-750 MKII. These amps have preloaded curves to optimize the performance of Invisible Series speakers and woofers. Preconfigured curves for various finish types and thicknesses allow for effortless calibration without the need for additional Sonance invisible series series# Sonance DSP Amplifiers are rated down to 4 Ohms and are stable to 2 Ohms. Never run more than two Invisible Speakers in parallel on one amplifier channel. NOTE: Pay attention to Sonance IS speaker-rated RMS power handling. Its amazing frequency range starts at 30 Hz and, depending on the application, extends up to 250 Hz, strictly measured with a maximum of +/- 3 dB permissible tolerance.Select an amplifier with max RMS watts per channel at 4 ohms that closely matches or is less than the IS speaker’s rated power handling (see page 16). ![]() It is ideal for installation and retrofitting in drywall.Ī completely invisible 15 inch subwoofer with more than twice the cone area as the SONANCE IS10. The surface material of the speaker cover/diaphragm is designed similar to the drywall material plasterboard. Responsible for this is the self-developed 10-inch bass loudspeaker, which perfectly reproduces the classic hi-fi woofer with the full range of sound downwards. The outstanding low-frequency reproduction technology used by Sonance does not skimp on magnet size and delivers a great deal of precision right down to the lowest frequency range. Only then does this subwoofer become completely invisible. The sound radiation takes place on the entire membrane surface of the subwoofer. Uses a high-precision depth gauge and embedded positioning discs to measure the thickness of a coating applied to the surface of a Sonance invisible speaker, allowing for consistent coating and performance within specifications every timeĬeiling speaker, invisible speaker, wall speakerĮxpandable with completely invisible subwoofersĪ completely invisible subwoofer for many applications. SONANCE DEPTH IDENTIFICATION SENSING CALIBRATION (DISC) SYSTEM.Proprietary Sonance CDX offers a uniquely smooth off-axis frequency response for greater fidelity and coverage, as well as nearly 180° horizontal and vertical coverage CROSSOVER WITH CONSTANT DIRECTIVITY (CDX).The diaphragm is split into two active areas that are completely isolated to allow for ultra-low distortion sound transparency like never before High-bandwidth midrange and high-frequency converters that use the flexible wave principle and deliver velvety-smooth mids and crystal-clear highsįiberglass woofer coupled with an acoustically inert diaphragm to move an air pocket like a piston for robust and powerful bass The drivers are not only tried and tested in the private sphere, but also in the high-quality sales rooms of Chanel, Dior, Luis Vuitton or Yves Saint Laurent.Ī series of advances in invisible speaker design for unparalleled acoustic performance from an invisible speaker A passive, self-resetting overload protection for each loudspeaker chassis is integrated as standard. Different models serve dry construction or masonry installation. They can be used with any standard hi-fi or home cinema amplifier. The technology, which has been tried and tested over decades, has been patented several times. These high-quality speaker models are completely hidden under the plasterboard or wallpaper. Please note the different installation depth. It comes from the factory with a rear back box. The IS6T is the version of the IS6 with an adjustable transformer for commercial 70V/100V speaker systems.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |